Showing posts with label stripping. Show all posts
Showing posts with label stripping. Show all posts

Sunday, 24 January 2021

A UniCoFil vase

Back in August, I did some more prints with the UniCoFil filament after replacing the heatbreak. It's possible that replacement wasn't necessary, but I will never know. Even after that, the stripping continued, though possibly not as often or as much. After printing out a failed hexagon vase that simply came apart at a layer that had stripped, I changed the filament settings to a) have a 1.0 extrusion multiplier, and b) extrude at 230°C. That eliminated the stripping, and I was able to print this nice small vase:



Just goes to show that each filament has its own best settings. 

Sunday, 5 July 2020

Stripped again, and out of tubes

I was trying out some semi-transparent blue filament from UniCoFil. The temperature tower had quite a bit of stringing, so I tried with 2mm retraction. That, unfortunately, led to stripping when the next temperature tower got to 195C. Despite trying to help the filament come out, unloading didn't work, so I had to snip the filament and open up the extruder.

TIP: When snipping the filament, do so with as much filament above the PTFE tube as possible, to more easily grab it later.



I disassembled enough to have the heater assembly free and tried a cold pull, but there wasn't enough filament sticking out to get a good grip. So I unscrewed the heatsink (this time the heatbreak didn't follow) and could get the PTFE tube out easily. Not so the filament. I tried heating the tube on the bed and then pulling, but again with not enough to pull on. Eventually I used a small hex wrench to push out out from the other end, which worked.

Then I put the PTFE tube back in the heatsink, which was a mistake. I put it so far in that I couldn't screw the heatsink onto the heatbreak, and I wasn't able to pull it out without destroying it. Fortunately, I had a second one. Need to get more replacements, and maybe just a spare of each part.

Having mounted the heatsink on the heatbreak, I could insert the PTFE tube, but not quite enough, now the end would block the gears. So I took it apart again, pushed the PTFE a bit further in, and then it looked OK from my point of view. Not so from an actual functional point of view, it was high enough to hit the gears still. It needs to be barely visible above the edge of the hole.

I tried to align it better, but it took more squeezing than it really ought to, and one I had it in, the nozzle ended up being too low, possible because I couldn't screw the heatbreak far enough in. I will order a bunch of new tubes and spare other things, take the whole shebang apart, and then try first to install from fresh with a new tube, if that doesn't work then replace the heatsink - I think the black insert inside it has gotten damaged.

Monday, 4 May 2020

Nothing good lasts forever

Hot (or rather, not so hot) on the heels of boasting of my many successful prints comes a tale of woe and sorrow! Woe! Sorrow! Or at least some technical problems.

While printing a faucet filter tool of presumably the right size for ours faucets (I was too lazy to measure), my white filament ran out. Supposedly, the printer should handle this nicely, running an unload procedure immediately. For whatever reason, it didn't, just letting the filament continue through until it was past the drive and thus the point of no return. Apparently, but I didn't know at the time, it's feasible to just feed in more filament immediately, but I tried re-running unload, then pushing the filament piece further down. To no avail, it was stuck.

Opening the side (which hinges up nicely), I found a lot of white debris (it had ground down the end of the filament). After vacuuming most of it up, this was the sight that greeted me:


Taking a closer look with my proper camera, it was clear that the filament sat in a PTFE tube and wasn't a giant blob or anything.



So I tried pushing some more, at higher temperatures, but it wasn't budging. Eventually, I had to take the hotend assembly out, and since I'd probably need to take out the nozzle anyway (one page suggested removing the nozzle and then heating), I would swap to my 0.8mm MegaNozzle shown below (banana for scale):


After getting a set of inverted hex bits (very useful!), it was easy enough to unscrew the nozzle, but that didn't help with the blockage. Fortunately for me, they had designed the whole thing so that taking out the hotend is relatively easy, and I was able to unscrew the heatsink and heatblock. They advice against unscrewing the heatblock, but I didn't see how to avoid it, since it's not really accessible. Anyway, with that out, I was able to heat it in the oven and carefully puuuull out the filament until it went "plop" and popped out. This was essentially the classic cold pull, though possibly a bit too cold due to not having the right tools right at hand at first. The PTFE tube needed replacement, but fortunately my kit came with two spares - how prescient!


So I reassemble the whole thing and run a test without filament - after all, I need a nozzle in there first, which requires 285C. Alas, the heating is bad - it heats up, but very slowly, at 100C about 1C per second. I didn't let it run for long enough to get up to full temperature, it took over a minute to get to 135C. To check that it wasn't the thermistor misreading it, I poked an old PLA print at the heat block, but it only deformed slightly, so it definitely wasn't doing runaway heating. That's something at least, overheating could be quite dangerous. But I'm still stuck with bad heating. I double-checked the wiring in the board, and the resistances and voltage were correct. So either there's a loose wiring in the heatblock end, or... something else.

Saturday, 16 January 2016

Low-tech solutions to high-tech problems

I've been leaving the printer alone for the week since last weekend's Nyloc dropout in the X carriage. This afternoon at TGIF I realized how to get it back in most easily: A thin flat stick and a bit of sticky-tack. The thin flat stick ended up being a steak knife, but it worked. I swapped the screws out for slightly longer M3/16 screws, giving myself a bit more leeway to get the mount in. I also had to file  a bit off the mount, since it didn't print so nicely around the slots where it had to retract.

The fan does make it difficult to see what's going on, and it may end up running into the clamps holding on the glass plate if the print is larger. But oh, my, does it print well now. Did a trio of previous designs, and they are certainly much cleaner. The holes are still a bit small, but with the fan on I probably should redo heat and extrusion amount testing.

But before that, I want to print stuff! Printed the hex bit, the fan mount, a new dog bag wire endstop (that I had to recreate almost from scratch, but got it better), and a dream weaver frame.



One guy at Make Munich today trying to sell my on his printer proudly proclaimed that the firmware and slicer software was all of their own making. To which I had to say, "You say that like it's a good thing". The Marlin firmware and Slic3r are both doing quite well for me.

I've had to move my machine into my own room, since the noises it makes gives my wife a headache. I hope the wobbliness of the temporary table doesn't do too much damage. On the bright side, it forces me to be in my room for other purposes than sleeping, so I'll probably end up cleaning up a bit:)

As a final print tonight, I wanted to do a battery holder to organize my charged/uncharged batteries. But the filament stripped partway through:( Not the first time it has stripped, either. If it happens more, I'll have to (argh!) take the extruder apart and clean the hobbed bolt, I guess.

Monday, 28 December 2015

The key to success: Tighten your gear shafts!

Got a suggestion to print from an SD card instead of over the USB link, so I acquired a plain 32GB card, and after poking a bit at Linux got it to work. Except that the Marlin doesn't recognize it at all (and the USB connection resets whenever I insert the card).

Looking a bit more at what the two jumpers do. JP14 atop the board appears to be the Autoreset, necessary when uploading firmware, but might interfere with the SD card reader due to a shared reset pin. Taking it off doesn't change the reset behaviour, though, so I'll leave it on.

JP15 switches between power from USB and power from the PSU. According to this, having it away from the connector blocks means USB power, and I have it towards the connector blocks, so that should be OK. But just because I'm paranoid, I'll try a print with the opposite JP15 setting.

Once again, the extruder gets set to 200C and the bed does not get set. Also, the X axis got stuck moving towards home. That is with an admittedly slack belt. Tightened somewhat and restarted.

An annoying thing about Slic3r taking over the heating and homing is that it does the heating pause by inserting a long pause. During that time, the print cannot be aborted.

X axis problems got worse, now it can't home at all. Time to check if the motor rod is properly attached. Inspecting a stuck Home command with a flashlight shows that the rod does turn while the gear doesn't. That's one mystery solved. Unfortunately, I have no small enough hex wrench in the house. Fortunately, a tiny Philips works in a pinch.

I expect the motor would be more stable if the rod has a flat side, but alas it doesn't. I suppose I could grind it down with my Dremel (leaving tiny pieces of metal all over the place:) For now, I will just retighting and see what happens.

Again the heated bed takes quite a while and/or several attempts at setting it before it started heating, and the extruder temperature got set to 200 despite the Slic3r settings. The result looks unsurprisingly somewhat soft in the corners, presumably because there's time for a little bit extra filament to ooze out:


Tried running Slic3r on the command line, inspecting the resulting gcode. Even there, it ignores the settings, but running the Slic3r UI takes it into account. Noticed that the --load command allows multiple files to be specified, adding the ~/.Slic3r/filament/Simple Mode.ini file got the temperature right. So apparently the presets section doesn't load the right thing. But there's also a simple.ini that gets generate along with the slic3r.ini, which contains all the right settings. Pointing at that instead.

Found a hex bit set that was a gift from Ric a year ago, which contains tiny hex bits. Tightened X and Y considerably. Thanks, Ric! I still think a flat-side shaft would be better.

Took a couple of tries before I got this right - turns out it now heats the bed first, then homes and heats the extruder. Except sometimes the bed seems to get confused and either not heat or keep heating. Also, using simple.ini is not a good idea, but pointing at the three Simple Mode.ini files works (as long as you quote the arguments with spaces instead of backslash-escaping them). The entire command line is

/home/lars/Slic3r/bin/slic3r $s --load "/home/lars/.Slic3r/filament/Simple Mode.ini" --load "/home/lars/.Slic3r/printer/Simple Mode.ini" --load "/home/lars/.Slic3r/print/Simple Mode.ini" --output "$o"

Ok, so now it heats up the bed first, then the extruder, then waits for a minute before printing. Also, it's harder to trick into not printing in the middle. Ah, well. The skew is utterly gone now, to be replaced with a stringiness that I at first guess would say temperature or extrusion amount problems.


The temperature is easy to test, and I got decent results with 200 before, so let's go there.


Stringiness persists. Odd. Looks like too little filament. Tried extrusion multiplier of 1.1:


This was abandoned partway through as no filament was coming out. I marked the filament and made it extrude a set amount, but nothing came out.  Then I turned off the motors and pulled out the filament. It was stripped along one side:


Reinserting it and running again gave pretty nice results:


It looks a little blobby in the corners, and the top layers hang down a bit. I'll try at 190. After that I can attempt increasing the acceleration. This time, since it's been a bit hard to get off the print, I'm adding a raft, just to see how that works.


Raft was hard to get off. Not trying that again until I see a real need for it.

Upping the acceleration to 1/2 of the original:

#define DEFAULT_MAX_ACCELERATION      {1000,1000,150,2500}

#define DEFAULT_ACCELERATION          1000
#define DEFAULT_RETRACT_ACCELERATION  1000

This definitely helped on the corners, I'll try putting it all the way back up. The lid of the cube still sags a bit, and there are gaps between the lines. 


I wish I could add more skirts, it only barely gets to start extruding, and if any drooling happens while it waits for a minute in the corner, that's likely to get stuck in the main print, as can be seen in the bottom-left corner above.

Trying with a 1.1 extrusion multiplier.



Apparently the thing I can add is a "brim", but that actually connects to the object, not what I want. Also in this print tried lowering the temperature to 180 (185 for first layer) to see what effect that has on the corners and top sagging. It still has one corner with issues, and there's a bit of ridginess to one side:


Reducing extrusion multiplier again. And because it's getting late and this will probably be the last print of the day, I'm doing an actual useful thing: A wire clamp for the back of some LED tubes, with a nut-and-bolt arrangement for affixing a back plate. It's a continuation of the earlier design by Thomas Riedl. Also looks slightly like a space ship:


And finally, a progression of the prints that have brought me here over the last few days: